Fitment: For Honda XL700V Transalp (non-ABS) 2008-2014 For Honda XL700V Transalp (ABS) 2008-2014 For Honda XL1000V Varadero 2003-2012 For Honda VTR250 2009-2014 For Honda CB250F (with digital trip/odo) 2015 For Honda CB300F 2015-2018 For Honda CB400SF 2008-2017 For Honda CB400X 2013-2016 For Honda CB400F 2013-2015 For Honda CB500F 2013-2018 For Honda CB500X 2013-2018 For Honda CB600F Hornet 2007-2013 For Honda CB650F 2014-2018 For Honda CB1000R 2008-2018 For Honda CBR1000RR 2004-2018 For Honda CB1100 (non-ABS) 2010-2013 For Honda CB1100 (ABS) 2010-2013 For Honda CB1300 S/F 2003-2015 For Honda CBF600 2008-2012 For Honda CBF1000 F/FA 2006-2009 For Honda CBR250 2015 For Honda CBR300R 2015-2018 For Honda CBR400R 2013-2015 For Honda CBR500R 2013-2018 For Honda CBR600F 2011-2013 For Honda CBR600RR 2003-2018 For Honda CBR650F 2014-2018 For Honda CMX300 Rebel 2017 For Honda CMX500 2017 For Honda CRF250L/M All Years For Honda Crossrunner All Years For Honda CTX700 (w/o DTC) 2014-2017 For Honda Fury 2010-2018 For Honda Interstate 2010-2016 For Honda NC400X 2013-2015 For Honda NC700 S/X 2012-2017 For Honda NC750 S/X 2014-2018 For Honda NT700V Deauville 2006-2015 For Honda Sabre 2010-2012 For Honda Stateline 2010-2017 For Honda VFR800 Interceptor 2005-2013 For Honda VFR800X All Years For Honda VT400 (FI model) 2009-2014 For Honda VT750C (FI model) 2007-2017 For Honda VT750S (FI model) 2007-2009 For Honda VT1300 (All) 2010-2016 For Honda VTX1800 2005-2012 For Honda XL125V Varadero 2007-2014 For Honda TRX ATVs (FI model) All Years For Honda CB300R 2018-2019 For Honda CTX1300 2014-2015 For Honda ST1300 2008-2015 Condition: Light Source Color: Red, Blue, Green Item Name: Speed Gear Display Indicator Size: 4cm x 4cm x 4cm / 1.57in x 1.57in x 1.57in Features: - Displays current gear number - Indicates gears from 1 to 6, including neutral - Fast gear detection compared to indicators using speedometer or tachometer signals - Flexible mounting options for display Installation: Locate the RED 4-pin male diagnostic connector (DLC), typically near the ECU. It may have a removable cap and could be partially covered with black tape. Setup Procedure: - After installation, turn on the ignition. The display will count down from 6 to 1, indicating memory is cleared. - Lift the rear wheel using a stand and start the engine in neutral. (If no stand is available, setup can be done while riding on a long, straight road with light traffic.) - The display will blink "1". Engage first gear, release the clutch, and maintain RPM above idle. The display blinks faster during learning mode. - When the display shows "2", shift into second gear. - Repeat the process through all gears (up to 5th or 6th). - Once programmed, the display will count up from 1 to 6 when ignition is turned on, indicating normal operation. Reset Instructions: If gear indication is incorrect, reset the unit: - Turn on the ignition. When the display shows 5, 4, 3, immediately turn off the ignition. - Repeat this on/off cycle five times in succession to complete reset.